Router Setup Wizard. Welcome 2. Check Connection 3. Configure Router 4.
|Published (Last):||12 April 2013|
|PDF File Size:||16.29 Mb|
|ePub File Size:||2.5 Mb|
|Price:||Free* [*Free Regsitration Required]|
Quick Links. Download this manual See also: Administrator's Manual. Table of Contents. Aggregation services router broadband network gateway pages.
Small business wireless-g vpn router with rangebooster pages. A listing of Cisco's trademarks can be found at www. Third party trademarks mentioned are the property of their respective owners.
The use of the word partner does not imply a partnership relationship between Cisco and any other company. The RVW features multi-function operation allowing the device to function as a wireless router, bridge, or access point. If the LED is continuously lit green, the Cisco RV is connected to a device through the corresponding port 1, 2, 3, or 4. When the button is pushed in, power is on.
Power Port—The power port is where you connect the AC power cable. Verify that the surface is smooth, STEP 1 flat, dry, and sturdy. The cable or DSL modem is now connected to the router.
In this example, the LAN 1 port is used. STEP 5 Use only the power adapter that is supplied with the device. Plug the other end of the adapter into an electrical outlet. You may need to use a STEP 6 specific plug supplied for your country.
Launch a web browser and enter Use the links on this page to jump to the relevant configuration page. By default, this page appears when you start the Device Manager. Navigating through the Pages Use the navigation tree numbered 1 in Figure 1 located in the in the left pane to open the configuration pages.
You can then make changes and provision advanced features using the Device Manager. This is used if the primary DNS server fails.
Password Enter your password assigned to you by the ISP. The default MTU size is bytes. However, you can change this setting if required by your ISP. The profile is added to the Profile Table. You can STEP 2 use only alpha-numeric characters and the hyphen. Click Save. Page 49 , , , , , and This value is the priority component of the bridge identifier of the network node.
The default is Page Configuring Jumbo Frames Frames feature allows the switch to send jumbo frames within the LAN containing up to 9, bytes of data per frame.
After support is enabled, devices on the LAN side of the network can exchange traffic that contains jumbo frames. Depending on the use of -F and -C, this is either route cache misses -F or hits -C. Page 52 Gateway—Use gateway.
R—Reinstate route for dynamic routing. D—Dynamically installed by daemon or redirect. M—Modified from routing daemon or redirect.
You can enable or disable ports, configure if the port is half- or full-duplex, and set the port speed. Page 57 Enter the user e-mail address for the TZO account. Enter the user key for the TZO account. Page Configuring Ipv6 Internet connection you have. See the sections below for detailed instructions.
The default IPv6 address for the gateway is fec You can change this bit IPv6 address based on your network requirements. Using a delegation prefix, you can automate the process of informing other networking equipment on the LAN of DHCP information specific for the assigned prefix. Page 66 Enter the prefix lifetime, or the length of time during which the requesting router is STEP 6 allowed to use the prefix.
The MAC address is a unique series of numbers and letters assigned to every networking device. With MAC address filtering enabled, wireless network access is provided solely for wireless devices with specific MAC addresses.
Page General Network Security Guidelines Combine letters and numbers to avoid using standard words that can be found in the dictionary. General Network Security Guidelines Wireless network security is useless if the underlying network is not secure. These settings apply to all of the wireless networks. Page 73 STEP 6 wireless frames. Select a channel from the list of channels or choose auto to let the Cisco RVW determine the best channel to use based on the environment noise levels for the available channels.
For example, if the Cisco RVW has many wireless users, you can prevent users from accessing other parts of the network.
The personal authentication is the preshared key PSK that is an alphanumeric passphrase shared with the wireless peer. Page Configuring Mac Filtering If you want to see the password as you are entering it, check the Unmask Password box. These keys are internal keys exchanged between the Cisco RVW and connected devices.
A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. The limit applies to both long and short frames of a size less than or equal to the RTS threshold.
Then click Configure via PIN. The device should begin communication with the Cisco RVW. You then specify how and to what devices the rules apply. Page 91 Enable box and enter the IP address you want to use. Under Rule Status, choose Enabled or Disabled. You may want to configure a rule and choose Disabled if you want to enable it at a later time.
Attack prevention allows you to manage WAN security threats such as continual ping requests and discovery via ARP scans.
This setting is used as a diagnostic tool for connectivity problems. A malicious ActiveX control can be used to compromise or infect computers. Enabling this setting blocks ActiveX applets from being downloaded. The table displays currently blocked keywords. Page Configuring Port Triggering You can also specify a port triggering rule by defining the type of traffic TCP or UDP and the range of incoming and outgoing ports to open when enabled.
Page Enter the Destination IP address, or the address where traffic meeting the rule should be sent. In the Internal Port field, enter the port to which traffic should be forwarded. A DMZ is a sub-network that is open to the public but behind the firewall. It is recommended that hosts that must be exposed to the WAN such as web or e-mail servers be placed in the DMZ network. Repeat STEP 4 for each address to allow or block. Some machines are configured with static addresses. Page Creating Schedules Under Repeat, check Everyday to apply the schedule to all the days of the week.
STEP 5 Leave the box unchecked if you want it to only apply to certain days, and check the boxes next to the days you want to include in the schedule. You can also introduce timeouts for TCP and UDP sessions to ensure Internet traffic is not deviating from expectations in your private network. STEP Page DMZ servers. Page Click Add. Configuring VPN Users, page Using the Management Interface, page The remote clients must run VPN client software.
A certificate must be configured in order for RSA-Signature to work. Page Local Traffic Selector: Page To add a client, click Add. Uncheck the box to de-activate the user account. You can obtain a digital certificate from a well-known Certificate Authority CA such as VeriSign, or generate and sign your own certificate using functionality available on this gateway. STEP 2 The contents of the request are displayed. Page Configuring Captive Portal Settings It also prevents access to that port in cases where the authentication fails.
It provides an authentication mechanism to devices trying to connect to a LAN. The username and password are the credentials sent to the authenticating server the device running For example, limiting the outbound traffic helps you prevent the LAN users from consuming all of the bandwidth of the Internet link.
Cisco RV180 VPN Router
Cisco RV180 User Manual