DSL 502T MANUAL PDF

But if you do not have the manual for your router or you do not want to read the whole manual to find the default login information then you can use the quick guide below. To get to the router login page it's necessary that you are connected to the router. Open your web browser e. Chrome, Firefox, Opera or any other browser Type You should see 2 text fields where you can enter a username and a password.

Author:Mikashicage Moogurg
Country:New Zealand
Language:English (Spanish)
Genre:Sex
Published (Last):19 February 2017
Pages:64
PDF File Size:7.74 Mb
ePub File Size:3.82 Mb
ISBN:871-2-54061-690-9
Downloads:15179
Price:Free* [*Free Regsitration Required]
Uploader:Tautaur



Quick Links. Download this manual. Table of Contents. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. If a Registration Card for the product in question has not been returned to a D-Link office, then a proof of purchase such as a copy of the dated purchase invoice must be provided when requesting warranty service.

Except as otherwise agreed by D-Link in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the license granted by D-Link for the Software.

Software will be warranted for the remainder of the original Warranty Period from the date or original retail purchase. Page 6 Any hardware, software, firmware or other products or services provided by anyone other than D- Link; Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product.

Page 8 Remote Log The default subnet mask is DSLT The Modem may be reset to its factory default settings by performing a Restore settings operation within the management interface, see System Commands for more information. Connect the USB cable to the device. Click the Next button. Click Next. Page 15 7. Connect the Ethernet cable if you have not done so. Connect the ADSL cable if you have not done so. Page Introduction The Router is easy to install and use. A single computer may also be connected through the USB port.

The ADSL connection is made using ordinary twisted-pair telephone line with standard connectors. Page Front Panel Display A solid green light indicates a valid link on startup. Steady green light indicates a valid USB connection. Place the Router in a location where it can be connected to the various devices as well as to a power source.

The Router should not be located where it will be exposed to moisture or excessive heat. Page Network Connections If you wish to reserve the uplink port on the switch or hub for another device, connect to any on the other MDI-X ports 1x, 2x, etc.

However, you cannot use the same IP address since every computer must have its own Note IP address that is unique on the local network. From the Start menu on your desktop, go to Settings, then click on Network Connections. Click on the Properties button.

Page Windows 4. Double-click OK to confirm and save your changes, and then close the Control Panel. Page Windows 95 And Windows 98 6. Follow the instructions to install the files. Page 30 3.

Click OK twice to confirm and save your changes, and then close the Control Panel. Login to Home Page A new window will appear and you will be prompted for a user name and password to access the web-based manager. Home - Login window Page Configure The Router Internet. The Router must be configured to communicate with the systems that give it access to the larger network. Click either the Setup tab or the Go to setup wizard hyperlink ; the Setup window will appear. The first menu you see when clicking the Setup tab or the Go to setup wizard hyperlink is the Setup menu.

Page 34 If you are instructed by your ISP to change the Modulation type is used for your service, select the desired modulation type and then click Apply. The modulation types available are T, G. Page Configure Connection 1 For Pppoa 8.

Click the Apply button when you have entered all the information. The web browser will briefly go blank. You are now finished changing setting for the primary WAN connection known as Connection 1.

It is now necessary to save the changes you just made and restart the Router. Some of the settings do not need to be changed the first time the device is set up, but can be changed later if you choose. When the device is used in this manner, it is necessary to install additional connection software on any computer or server used to access the Internet. If the WAN connection state does not appear to Connected after a few minutes, go back to the Connection 1 Setup menu, check the settings and make sure they are correct.

Select the desired Mode, Bridged or Routed. Many users will be able to use the default settings. Page Configure Connection 1 For Clip 1. Page Create A New Connection Use the New Connection procedure to create new connection used for accounts that supports multiple virtual connections.

For more information on creating and maintaining virtual connection, see Multiple Virtual Connections in the following chapter on Note Advanced Router Management. Page 43 Figure 3- Setup a New Connection — Connection 2 Remember to save new configuration settings using the Save All button when you have made all the intended changes.

Page 44 5. Figure 3- Setup a New Connection — Connection 3 To delete any existing connection, go to the configuration menu for that connection and click the Delete button. When you are finished making changes to the Router settings, follow the instructions here to save the new settings. It will take a second or two to perform the save.

After the save is completed, a message appears in a new menu see below. When enabled, it allows other devices that support UPnP to dynamically join a network, obtain an IP address, convey its capabilities, and learn about the presence and capabilities of other devices. This menu can be accessed directly by clicking on the LAN Clients button or hyperlink in the Advanced setup menu.

Page Port Forwarding Figure Page 54 5. Figure 4- 5. Port Forwarding User Rules Management 2. Type a Rule Name in the space provided. This will block all traffic from the WAN port to the specified client. Remember to save the configuration changes. Access Control menu Page 58 5. Type a number for the Port Map in the space provided. This is the local port being forwarded to. Click the Apply button to create the new rule.

The new rule will appear listed in the table of custom port control rules. IGMP packets are used to control multicasts and discontinue multicasts to individual IP addresses when they are no longer needed. This is used to specify that all packets destined for a particular network or subnet use a predetermined gateway. It also supports use of password protection, which requires password verification for RIP requests. These additional connections occupy the same bandwidth used for ADSL service.

Additional PVC connections can be added to establish a private connection to remote offices or maintain a server accessible through the WAN port. Page User Management 2. Type in the new Password in the entry field provided. Type in the new password again in the Confirm Password field.

If desired, change the Idle Timeout value. Click Apply. User Management menu Page System Commands Router will revert to the previously saved configuration upon rebooting the Router. Figure Remote Log menu Select the Log Level from the pull-down menu. Save the latest firmware version to a file on your computer or an accessible TFTP server. Tools — Ping Test window To Ping a device, first enter the IP address of the device that you wish to Ping into the first field, the Packet Size in bytes in the second field, and finally, enter the number of times you wish the Ping function to attempt a connection to the desired device into the third field.

Test for F5 or F4 connection on the near segment or end-to-end. Status display links Click the hyperlink or menu button for the desired Status window. Network Statistics window Choose the desired interface at the top of the window and then click Refresh to view Ethernet network statistics.

Connection Status window Click Refresh to view connection status information. DHCP Clients window

LEONARDO PADURA HEREJES PDF

D-Link DSL-502T User Manual

.

AGATHA CHRISTIE ASESINATO EN LA CALLE HICKORY PDF

D-Link DSL-502T-GenII Default Router Login

.

FORMATO SAV 005 PDF

D-Link DSL-502T Manuals

.

DIDYSIS GETSBIS PDF

.

Related Articles