SONY HVR-MRC1 MANUAL PDF

If you get stuck in repairing a defective appliance download this repair information for help. See below. Good luck to the repair! Please do not offer the downloaded file for sell only use it for personal usage! Looking for other manual?

Author:Faenos Dairg
Country:Latvia
Language:English (Spanish)
Genre:Love
Published (Last):15 January 2018
Pages:55
PDF File Size:15.73 Mb
ePub File Size:20.7 Mb
ISBN:342-1-99914-607-9
Downloads:39402
Price:Free* [*Free Regsitration Required]
Uploader:Nesho



The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi. The actual usable capacity may be slightly less because administrative files etc. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors.

Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. Look for parts which, through functioning, show obvious signs of deterioration. Flexible Circuit Board Repairing Keep the temperature of the soldering iron around C during repairing.

Do not touch the soldering iron on the same conductor of the circuit board within 3 times. Be careful not to apply force on the conductor when soldering or unsoldering.

Unleaded solder Boards requiring use of unleaded solder are printed with the leadfree mark LF indicating the solder contains no lead. Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.

Unleaded solder melts at a temperature about 40C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to about C. Caution: The printed pattern copper foil may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscous sticky, less prone to flow than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.

Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. Lead Free 40 IC. In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply 8. These following method is available to prevent this. Method: Use the DC input terminal.

And this unit is sent error code to camera. LCD screen. Cash overflow by transfer rate delay of Be sure that the CompactFlash you are using is the recommended type. The selection clip is not found.

Be sure that the CompactFlash you are using is the recommended type. Reformat the CompactFlash using this unit again, after reformatting The filesystem of CompactFlash is broken.

CompactFlash recognition error Check the type you are using. Error related to i. LINK Turn this unit off and then back on. It is generated the error by the power supply Turn this unit off and then back on.

It is generated the error by the power supply control from sub CUP to each Turn this unit off and then back on. It could not enter to the sleep mode. Turn this unit off and then back on. The input video stream is abnormal. The recording animation could not Turn this unit off and then back on.

Communication abnormality between Turn this unit off and then back on. CompactFlash and main CPU. LINK error. It abnormal is generated by the file system. Reformat the CompactFlash using this unit. Sub CPU cannot control each device. Sub CPU farm is not written.

Fatal error of originating hardware. Fatal error of originating software. Reception buffer overflow. Error code of main CPU firmware. Do not insert the cable insufficiently nor crookedly. When remove a connector, dont pull at wire of connector. It is possible that a wire is snapped. When installing a connector, dont press down at wire of connector. Cut and remove the part of gilt which comes off at the point.

Be careful or some pieces of gilt may be left inside. HELP Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. Some chip part will be indicated as follows. In such cases, the unused circuits may be indicated.

Refer to the mount table for each function. All variable and adjustable resistors have characteristic curve B, unless otherwise noted. C : adjustment for repair. Measuring conditions voltage and waveform Voltages and waveforms are measured between the measurement points and ground.

They are reference values and reference waveforms. When indicating parts by reference number, please include the board name. Ne les remplacer que par une pice portant le numro spcifie. C 0. C B 25V 0.

It is included in TK complete board though neither of these are supplied. FB S3. There are a few cases that the part printed on diagram isnt mounted in this model. C : panel designation Chip parts. Some delay should be anticipated when ordering these items.

The mechanical parts with no reference number in the exploded views are not supplied. Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. Use the correct part for the each camera or model. See the chart below Note:. Part No. Refer to page for mark 0. S Part No. Description 0. TK Ref. Q Q Q Part No. Description 33 22 33 33 33 33 33 33 33 33 33 10K 10K 5. The printed matter is not supplied.

If required, please order it with the part number below. LINK cable and using batch files. Kind of history information This set records the following history information: 1 Error codes latest 10 codes 2 Accumulated POWER ON time in minute 3 Accumulated recording time in minute 4 Accumulated playback time in minute 5 Accumulated files created 6 Accumulated CF card detection count. LINK cable. Note: Remove the Compact Flash card if it has been inserted in the set.

Operation is not assured if rhe above OS has been upgraded. Install the driver in the following procedures. Once this work is performed, further installation is not required later on. Note: If the PC restarts after the driver installation completes, starts from the procedure No.

TOP247YN DATASHEET PDF

Sony Hvr-mrc1 Service Manual Ver 1.2 2009.03 Rev-2 (9-852-266-13)

Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Sony HVR-MRC1. If looking through the Sony HVR-MRC1 user manual directly on this website is not convenient for you, there are two possible solutions:. Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual.

DUELING BANJOS BANJO TAB PDF

Sony HVR-MRC1 User Manual

.

DESCARGAR LIBRO QUIMICA ORGANICA JOHN MCMURRY PDF

Sony HVR-MRC1 user manual

.

DHAMU SAMAYAL IN PDF

Sony HVR-MRC1 Camcorder Accessories User Manual

.

Related Articles